Anderson Detector Shafts

Anderson Excalibur Long Shaft - 0811

This is a well balanced shaft that replaces the factory style S rod. Works with the new style Minelab Excalibur 800/1000. Must use factory lower fiberglass shaft (not included)

$119.99

Anderson Excalibur SCUBA Shaft - 0812

This product significantly reduces the overall lenght of your detector. Works with new style Minelab Excalibur 800/1000. When using this setup the diver has more control and can work closer to targets.Factory fiberglass dive shaft must be used (not included)

$119.99

Anderson Excalibur Over Under - 0813

This is the newest of Excalibur Shafts. This is a very well balanced system with the electronics mounted under the top rod.It is more compact than our long shaft and almost the same length as the stock s rod. Handle and arm cuff can be adjusted in multiple locations. Extra snap pins holes were also added for more adjustment in the lower end.

$119.99

Anderson X-TERRA Shaft - 0827

The Anderson X-TERRA Shaft is 30.5" long with adjustable handle and armcuff. This shaft also comes with an Anderson Stand and instructions. NOTE: Black Only

$119.99

Anderson Excalibur Extension Shaft - 0814

Here is an innovative product that allows you to retain your factory S rod and enjoy the benefits of a well-balanced detector. The Anderson Shaft Extension attaches directly in to your stock S rod and uses the arm cuff fastening bolt to secure it. The result is a lighter feeling and more balanced machine. Constructed of the same materials as other Anderson Products for years of durability and performance.

$29.99

Anderson Minelab Gold Shaft - 0824

This 33" straight shaft fits Eureka Gold, SD 2100/2200, GP 3000 and the Sovereign with the 1 9/16" bolt pattern. Comes with adjustable handle and cam lock. There are 6 lower rod spring pin holes for lots of lower rod adjustability.

$89.99

Excalibur 12v Nicad Battery Pack - 0915

Minelab Excalibur replacement battery. 12 volt Nicad 600mah. Discharge rate 8 amps. Fits old and new style pods. 9v connector style.

$49.99

Anderson Excalibur Knob Guard - 0916

Anderson Excalibur Knob Guard. Great way to protect your detector control knobs. Comes with mounting hardware and instructions. Available in Anderson Blue, Sandtex Black, SCUBA Yellow and Minelab Green.

$39.99

Excalibur Replacement Knob Set - 0919

5 pack of knobs to replace stock excalibur knobs or any onther machine that uses a 1/4" or 6.3mm shaft. These knobs are made from plastic with a brass insert with a set screw on the side. They are larger than stock units and with the pointer its easy to set them without having to look at them. Get them in Blue, Green or Yellow.

$19.99

Anderson Excalibur Hip Mount Kit - 0921

Anderson Excalibur Hip Mount Kit allows you to hip mount your electronics. No tools needed and comes with adjustable waist belt. Available in Green, Blue, Yellow and Black.

$29.99

Anderson Garrett Long Shaft - 0821

This shaft for the Garrett water machines eliminates the looseness and wobble found in the stock factory setup. It is a complete system featuring our new straight shaft and Zero Flex HD Series lower rod. There's plenty of adjustability to suit any user. This model fits the Infinium and Sea Hunter Mark 2 as well as other Garrett water machines with the 2" electronic bracket hole spacing.

$149.99

Anderson Garrett Regular Shaft - 0822

This shaft for the Garrett water machines eliminates the looseness and wobble found in the stock factory setup. It is a complete system featuring our new straight shaft and Zero Flex HD Series lower rod. This model fits the Infinium and Sea Hunter Mark 2 as well as other Garrett water machines with the 2" electronic bracket hole spacing.This is a compact setup with great balance. Lenght is 27"

$149.99

Anderson Garrett SCUBA Shaft - 0823

This shaft for the Garrett water machines eliminates the looseness and wobble found in the stock factory setup. It is a complete system featuring the shaft and Zero Flex HD Series lower rod. The length for the shaft and rod is only 24" so the diver has more control and can work closer to targets. This model fits the Infinium and Sea Hunter Mark 2 as well as other Garrett water machines with the 2" electronic bracket hole spacing.

$119.99

Anderson Fisher
Long Shaft - 0818

Fisher Long Shaft works with the 1280, CZ20, Impulse and will work with the new CZ21.Shaft is 39" and comes with a bracket that slides into the bottom of the detector housing. Housing can be mounted between the handle and arm cuff or in 3 other positions behind the cuff

$119.99

Anderson Fisher Regular Shaft - 0819

Fisher Regular Shaft works with the 1280, CZ20, Impulse and will work with the new CZ21.Shaft is 27" and comes with a bracket that slides into the bottom of the detector housing. Housing is mounted between the handle and arm cuff. This is a compact setup with great balance.

$119.99

Anderson Fisher Regular Shaft - 0820

The Fisher SCUBA shaft is 15" long and comes with a bracket the slides into the bottom of the detector housing. Made for the 1280,CZ20, Impulse and CZ21 Factory Fisher lower rod may be cut to get shortest length for best performance or purchase a 12" HD series lower rod for this model.

$99.99

Anderson Tesoro
Long Shaft - 0815

Tesoro Long shaft fits all the water models that Tesoro currently and previously produced including the Stingray, Stingray 2, Piranha, Sand Shark, and Tiger Shark. The detector housing can be mounted between the handle and cuff or in 3 other positions behind the cuff.

$149.99

Anderson Tesoro Regular Shaft - 0816

Tesoro Regular Shaft fits all the water models that Tesoro currently and previously produced including the Stingray, Stingray 2, Piranha, Sand Shark, and Tiger Shark. The detector housing is mounted between the handle and cuff. This is a compact setup with great balance. Shaft length is only 27"

$119.99

Anderson Tesoro SCUBA Shaft - 0817

Tesoro SCUBA Shaft fits all the water models that Tesoro currently and previously produced including the Stingray, Stingray 2, Piranha, Sand Shark, and Tiger Shark. When using this setup the diver has more control and can work closer to targets.

$99.99

Anderson Ultamite
Arm Cuff - 0913

The Anderson Ultimate Arm Cuff is made from high quailty aluminum with a sandtext black powder coat finish. Cuff also has foam pad on the inside and a 2" adjustable arm strap. Comes with black hardware. This will fit most makes and models with a 7/8" detector shafts

$24.99

Anderson Minelab
Explorer Arm Cuff - 0925

Replaces factory arm on Minelab Explorer.S,XS,II,SE,Quattro,E-Trac and Safari machines. Made from high quailty aluminum with a sandtext black powder coat finish. Cuff also has foam pad on the inside and a 2" adjustable arm strap.

$24.99

Anderson Detector Stand - 0917

Anderson metal detector stand fits most detectors with a 7/8" shaft or smaller. All you have to do is put in place and tighten the two thumb screws. Made of .5" UV resistant ABS. Great way to keep your machine up out of the water and dirt. Available in Black, Blue, Yellow, Red and Pink

14.99